Top 10 typical forklift mishaps ， forklift procedure ought to focus on these matters ！.

Do not take too lightly the forklift at work. If the operation is not good, there will be major crashes in mins, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the path and hangs on the roadside shelf, which almost triggers an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning has to be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the automobile to shed lateral stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must follow the website traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the lots must be in the most affordable placement that does not prevent the driving, and the gantry should be properly tilted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the driver's sight. In unique conditions, when the thing impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks ought to be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects Electric Forklift Truck for Warehouse and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as possible under the lots, and it should be kept in mind that the fork pointer ought to not touch various other goods or items. The lots ought to be supported with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots Stand-on Electric Pallet Stacker is lowered to enable very easy positioning of the load and extraction of the forks. .
6. It is restricted to fork items at high speed and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special conditions, such as the motorist does not leave the lorry's view and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubing oil and cooling water should be included.
2. Examine the security efficiency of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be as well sharp to prevent the propensity of " totally free switching";.
6. Adding and down the slope must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the gradient is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to make use of inertia force to get the goods.
6. It is not permitted to use braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844